Looking For A Blank Hockey....

[KingViper ●]

Is this possible? I need a blank hockey with no holes drilled. Only eye holes and a nose. I don't even want indentions for the holes. Is that how they come???ThanksViper

[WHiTE_SiDER ●]

Ken tarallo

[JoMaX ●]

<!--QuoteBegin-KingViper+Mar 26 2007, 08:35 PM<div class=\'quotetop\'>QUOTE(KingViper @ Mar 26 2007, 08:35 PM)</div><div class=\'quotemain\'><!--QuoteEBeginIs this possible?  I need a blank hockey with no holes drilled.  Only eye holes and a nose.  I don't even want indentions for the holes.  Is that how they come???ThanksViper<div align=\"right\"><a href=\"index.php?act=findpost&pid=211887\"><{POST_SNAPBACK}></a></div><!--QuoteEnd</div><!--QuoteEEndI am not really sure to be honest man.Have you tryed ken at www.frightstuff.com ?You might wanna go over there and have a look man.EDIT i dont know if you will find a Hockey Mask with no pre set hole's for drilling.

[WHiTE_SiDER ●]

<!--QuoteBegin-JoMaX+Mar 26 2007, 10:02 PM<div class=\'quotetop\'>QUOTE(JoMaX @ Mar 26 2007, 10:02 PM)</div><div class=\'quotemain\'><!--QuoteEBeginI am not really sure to be honest man.Have you tryed ken at www.frightstuff.com ?You might wanna go over there and have a look man.EDIT i dont know if you will find a Hockey Mask with no pre set hole's for drilling.<div align=\"right\"><a href=\"index.php?act=findpost&pid=211898\"><{POST_SNAPBACK}></a></div><!--QuoteEnd</div><!--QuoteEEndim pretty sure ken will do it

[CreepingDead ●]

I think most all blanks have the indents where the holes go.

[Crash ●]

Ken can hook you up over at FrighStuff. But like was said above, most hockey masks I know of will have the hole indents when vacced. That's just the way they are. You may find someone working in fiberglass that could help though. Good luck!

[KingViper ●]

<!--QuoteBegin-Crash+Mar 27 2007, 12:38 PM<div class=\'quotetop\'>QUOTE(Crash @ Mar 27 2007, 12:38 PM)</div><div class=\'quotemain\'><!--QuoteEBeginKen can hook you up over at FrighStuff. But like was said above, most hockey masks I know of will have the hole indents when vacced. That's just the way they are. You may find someone working in fiberglass that could help though. Good luck!<div align=\"right\"><a href=\"index.php?act=findpost&pid=211955\"><{POST_SNAPBACK}></a></div><!--QuoteEnd</div><!--QuoteEEndThanks everyone! What's his email address?? I don't see it listed on the site.Viper

[JoMaX ●]

<!--QuoteBegin-KingViper+Mar 27 2007, 07:43 PM<div class=\'quotetop\'>QUOTE(KingViper @ Mar 27 2007, 07:43 PM)</div><div class=\'quotemain\'><!--QuoteEBeginThanks everyone!  What's his email address??  I don't see it listed on the site.Viper<div align=\"right\"><a href=\"index.php?act=findpost&pid=212116\"><{POST_SNAPBACK}></a></div><!--QuoteEnd</div><!--QuoteEEndfxdude@earthlink.net

[horrorconcepts ●]

I can do it without the dents if you haven't found someone already <img src=\"http://forums.NIGHTOWLpro.com/style_emoticons/<#EMO_DIR#>/thumbsup.gif\" style=\"vertical-align:middle\" emoid=\":thumbsup:\" border=\"0\" alt=\"thumbsup.gif\" /> pm sent.